View 3583JM_771145.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(R)
3583
High Voltage, High Current OPERATIONAL AMPLIFIER
FEATURES
q WIDE POWER SUPPLY VOLTAGE: 70V to 150V q OUTPUT CURRENT TO 75mA q SLEW RATE: 30V/s q FET INPUT: IB = 20pA max q THERMAL SHUT-DOWN PROTECTION q HERMETIC TO-3 PACKAGE, ISOLATED CASE
APPLICATIONS
q PROGRAMMABLE POWER SUPPLY q PIEZO-ELECTRIC TRANSDUCER DRIVER q HIGH VOLTAGE CURRENT SOURCE
DESCRIPTION
The 3583 is a high voltage, high speed hybrid operational amplifier designed for a wide variety of programmable power supply and transducer driver applications. The 3583 operates over a wide power supply range (50V to 150V) and provides outputs up to 75mA. Laser-trimmed FET input circuitry provides low offset voltage (3mV max) and low input bias current (20pA max). Thermal shut-down circuitry protects internal circuitry from excessive power dissipation. Commercial and industrial temperature range models are available. The 3583's hermetic 8-pin TO-3 package is electrically isolated from all internal circuitry.
Offset Trim 3 4
V+ 2
5 -In 1 Output
6 +In
7 V-
International Airport Industrial Park * Mailing Address: PO Box 11400 Tel: (520) 746-1111 * Twx: 910-952-1111 * Cable: BBRCORP *
(c)
* Tucson, AZ 85734 * Street Address: 6730 S. Tucson Blvd. * Tucson, AZ 85706 Telex: 066-6491 * FAX: (520) 889-1510 * Immediate Product Info: (800) 548-6132 PDS-343D Printed in U.S.A October, 1993
1976 Burr-Brown Corporation
SBOS130
SPECIFICATIONS
ELECTRICAL
TCASE = +25C, VS = 150V, unless otherwise noted. 3583AM PARAMETER OFFSET VOLTAGE Input Offset Voltage vs Temperature vs Power Supply vs Time INPUT BIAS CURRENT(1) Input Bias Current vs Temperature vs Power Supply Input Offset Current vs Temperature vs Power Supply NOISE Voltage, 0.01Hz to 10Hz 10Hz to 1kHz Current, 0.01Hz to 10Hz INPUT VOLTAGE RANGE Max Safe Differential Input Max Safe Common-Mode Input Common-Mode Input Range Common-Mode Rejection INPUT IMPEDANCE Differential Common-Mode OPEN-LOOP GAIN Open-Loop Voltage Gain Open-Loop Voltage Gain FREQUENCY RESPONSE Unity-Gain Bandwidth Full-Power Bandwidth Slew Rate Settling Time: 0.1% OUTPUT Voltage Output Current Output Short Circuit Current Load Capacitance POWER SUPPLY Operating Voltage Range Quiescent Current TEMPERATURE RANGE (CASE) Specification Operating Storage JC = 4C/W No Load, DC Rated Load, DC Small-Signal RL = 10k CONDITIONS MIN TYP MAX 3 23 20 50 VCM = 0V Doubles Every 10C 0.2 VCM = 0V Doubles Every 10C 0.2 5 1.7 0.3 (V+) + |V-| V- to V+ VS -10 110 1011 || 10 1011 118 105 5 60 30 12 VS -10 75 * * 100 10 50 IO = 0 -25 -55 -55 150 8.5 +85 +125 +125 * * * * * +70 * * 20 * * * * * * * * * * * * * * * * * -20 * * * * * * MIN 3583JM TYP MAX * * UNITS mV V/C V/V V/month pA pA/V pA pA/V Vp-p Vrms pAp-p
Specified Temp. Range
Linear Operation
V dB || pF || pF dB dB MHz kHz V/s s V mA mA nF V mA C C C
94
*
0 * *
* Specification same as 3583AM. NOTE: (1) Inputs may be damaged by input slew rates exceeding 1000V/s. Inputs can be protected from signals exceeding 1000V/s by limiting input current to 150mA with external series resistors (pins 5 and 6).
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user's own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems.
(R)
3583
2
CONNECTION DIAGRAM
Top View TO-3
PACKAGING INFORMATION
MODEL 3583AM 3583JM PACKAGE 8-Pin TO 3 8-Pin TO 3 PACKAGE DRAWING NUMBER(1) 030 030
Optional Offset Adjust 100k to V+ Supply Offset Trim 5 -In +In 4
Offset Trim 3 2
+VCC 1 Output
NOTE: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix D of Burr-Brown IC Data Book.
ORDERING INFORMATION
MODEL PACKAGE 8-Pin TO-3 8-Pin TO-3 TEMPERATURE RANGE -25C to +85C 0C to +70C
8 6 7 -VCC
NC(1)
3583AM 3583JM
NOTE: (1) No internal connection. Optional socket available: 804MC
TYPICAL PERFORMANCE CURVES
TCASE = +25C, VCC = 150VDC, unless otherwise noted.
(R)
3
3583
TYPICAL PERFORMANCE CURVES (CONT)
TCASE = +25C, VCC = 150VDC, unless otherwise noted.
(R)
3583
4
TYPICAL PERFORMANCE CURVES (CONT)
TCASE = +25C, VCC = 150VDC, unless otherwise noted.
APPLICATION INFORMATION
Figure 1 shows the basic connections required to operate the 3583. Power supply bypass capacitors should be connected close to the device pins. Be sure that these capacitors have an adequate voltage rating. Input offset voltage and drift of the 3583 are laser-trimmed. Many applications require no external offset trimming. Figure 1 also shows connection of an optional offset trim potentiometer connected to pins 3 and 4. FET input circuitry reduces the input bias current of the 3583 to less than 20pA at room temperature. Input bias current remains nearly constant throughout the full common-mode range. Input bias current approximately doubles for each 10C increase in case temperature above 25C. Heat sinking can help minimize this effect by reducing the case temperature. Input circuitry of the 3583 is protected with series limiting resistors and input clamp diodes. The inputs can withstand the full rated supply voltage of 150V (common-mode or differential). THERMAL PROTECTION The 3583 has internal thermal shut-down circuitry that activates at a case temperature of approximately 150C or higher. As this circuitry is activated, the output current drive is reduced. As the case temperature returns to less than the activation temperature, operation will return to normal. A heat sink may be required depending on load and signal conditions. Note that a 75mA output may not be safe for all output voltages--see typical performance curve "Safe Operating Area". Applications such as current sources where output voltage may be low (or the opposite polarity of the output current) can overstress the output stage. The thermal shut-down circuit will normally protect the amplifier during a short-circuit to ground. It will not protect against short-circuit to one of the power supplies. The typical performance curve "Safe Operating Area" shows that the large stress occurring during this high voltage condition may cause damage if it exceeds 5ms duration. The thermal protection circuitry will not activate fast enough to protect the device from short-circuits to one of the power supplies. The package case of the 3583 is electrically isolated from all circuitry. No special insulating hardware is required. Although not absolutely required, it is recommended that the case be connected to ground.
V+ Optional offset voltage trim 100k circuit. 3 3583
+50V to +150V V+ 0.1F
4
R1
R2 G=1+ VO R2 R1
3583 VIN 0.1F Connect case to ground. V- -50V to -150V
FIGURE 1. Basic Circuit Connections.
(R)
5
3583
PACKAGE OPTION ADDENDUM
www.ti.com
3-Oct-2003
PACKAGING INFORMATION
ORDERABLE DEVICE 3583JM STATUS(1) NRND PACKAGE TYPE TO/SOT PACKAGE DRAWING LMF PINS 8 PACKAGE QTY 18
(1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device.
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Interface Logic Power Mgmt Microcontrollers amplifier.ti.com dataconverter.ti.com dsp.ti.com interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com Applications Audio Automotive Broadband Digital Control Military Optical Networking Security Telephony Video & Imaging Wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2003, Texas Instruments Incorporated www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless

▲Up To Search▲

Price & Availability of 3583JM

	To Download 3583JM Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .